BS PROFILE H 10

Plastic Expansion and Control Joints Profile

Description

PROFILE H BS 10 is a co-extruded plastic profile that can be used for the realization of non-structural expansion and control joints by directly bonding it to the screed or the concrete with BETONSEAL MS 2.0 sealant.

BS PROFILE H 10 is specifically designed for use with BETONGUAINA or BETONGUAINA.S waterproofing system to be followed by direct tiles bonding with BETON H-1 (dimensions in mm shown in fig.1): 

tl_files/nordresine/Scarichieprofili/BS PROFILE H10_fig 1.jpg

Advantages

PROFILE H BS 10 is:

  • is flexible and packed in rolls;
  • is installed by simply bonding it to the substrate with BETONSEAL MS 2.0 sealant after laying a base coat of BETONSEAL PRIMER;
  • has anchoring side wings with pre-drilled holes to increase the profile-sealant coupling tightness;
  • its middle portion is made of a very flexible material capable of withstanding even large deformations.
Packaging

10.5 m roll

BS PROFILE H 10

Plastic Expansion and Control Joints Profile

Application

Profile Preparation:

  • ensure that the profile is intact and free from oil, grease or other similar substances;
  • apply BETONSEAL PRIMER rubbing with either tampon or cloth over the entire surface made of semi-transparent PVC and avoiding to make the coloured middle portion dirty:

tl_files/nordresine/Scarichieprofili/BS PROFILE H_fig 2.jpg

  • if the temperature of the installation site is below 15°C, the profile must first be rolled out (up to the required length) and kept warm until the time of use. This procedure allows a proper lay out of the profile before installing it.

 

Profile Application:

once the screed has set, make a 80 mm wide and approx. 2.5 mm deep lowering over the joint, where the flush profile is to be inserted, using a grinding wheel (type Bosch GBR 14 CA) reinforced with a 80 mm diamond disc;

after shaping it as above-mentioned, the laying substrate shall be primed with NORPHEN FONDO IGRO:

 

tl_files/nordresine/Scarichieprofili/BS PROFILE H_fig 3.jpg

 

allow 15-20 minutes to rest and then apply BETONSEAL MS 2.0 sealant to the treated substrate:

 

tl_files/nordresine/Scarichieprofili/BS PROFILE H_fig 4.jpg

 

lay the profile over the joint and press to make the sealant pass trough the side wings holes;

with the exclusion of the coloured middle portion, the anchoring wings shall be completely covered with BETONSEAL MS 2.0:

 

tl_files/nordresine/Scarichieprofili/BS PROFILE H_fig 5.jpg

 

BETONGUAINA and BETONGUAINA.S waterproofing membranes shall be realized over the sealant when it is still fresh;

the next day to perform the direct bonding of the tiles with BETON H-1:

 

tl_files/nordresine/Scarichieprofili/BS PROFILE H1x_fig 6.jpg

 

Fig.6 shows how the particular shape of the upper side of part A allows the correct coupling between the profile and the tile.

 

Corner Splice Installation between Profiles

Once the first part of the profile is installed (from fig.2 to fig.5), the end of the profile to be placed at the angle shall be modified by removing both the side wings (Part A) and the lower part of the middle portion (Part B) of the profile not to let the ovelapping cause any height difference:

 

tl_files/nordresine/Scarichieprofili/BS PROFILE H_fig 7.jpg

BS PROFILE H 10

Plastic Expansion and Control Joints Profile

Features

Linear Mass Density

g/m

318 ± 8

Anchoring Wings Shore Hardness (A in fig.1)

A

72 ± 2

Middle Portion Shore Hardness (Part B in fig.1)

A

42 ± 2

Tensile Strength (5 mm/min)

-30°C

N/5cm

1240 ± 20

23°C

N/5cm

300 ± 10

40°C

N/5cm

200 ± 10

Elongation at break (5 mm/min)

-30°C

%

336 ± 13

23°C

%

404 ± 10

40°C

%

477 ± 10

Elastic Modulus at 100% (5 mm/min)

-30°C

N/mm

42.5 ± 0.8

23°C

N/mm

6.4 ± 0.3

40°C

N/mm

3.1 ± 0.1

Note: the test methods refer to the related standards as shown in the table.

BS PROFILE H 10

Plastic Expansion and Control Joints Profile

Warning and informations
  • The profile can be cut with scissors or shears.
  • Do not apply at temperatures below +5°C.
  • Do not expose to storage in direct sunlight
Preservation
  • 24 months in original packaging at temperatures between +5°C and +35°C.
  • The product is sensitive to sunlight