DEKOR-SEAL WAX

Protective wax for
DEKOR SEAL-S500 treated floors

Description

DEKOR-SEAL WAX is a protective agent based on wax and acrylic resins in water emulsion.

Because of its chemical nature DEKOR SEAL WAX is non-yellowing, glossy and capable of increasing the abrasion resistance level of the substrate on which it is applied by acting as a non permanent layer.

DEKOR-SEAL WAX is easily removed with STRIPPER PLUS and then reapply periodically.

DEKOR-SEAL WAX leaves behind a permanent lemon scent on the floor.

Usage field

DEKOR-SEAL WAX is specifically formulated to protect surfaces previously treated with DEKOR-SEAL S500 by wax coating.

DEKOR SEAL S500 OPACO can be treated if the loss of opacity can be accepted (opacity that will be restored only after the waxing layer complete elimination).

Since DEKOR-SEAL WAX has a very low volatile organic compounds (VOC) content and it does not damage any epoxy resin floors, it is indeed suitable to protect them. It is not advisable to use this product on areas where NORPHEN ESC cycle has been applied or that are covered by other antistatic / conductive products, since it would nullify all these very same antistatic / conductive properties.

Packaging

PE containers of 1, 5 and 10 liters.

DEKOR-SEAL WAX

Protective wax for
DEKOR SEAL-S500 treated floors

Application

First application on surface pre-treated with DEKOR-SEAL S500:

prior to the application of DEKOR-SEAL WAX, the surface must be thoroughly cleaned with DEKOR-SEAL CLEANER diluted 1:1 with hot water (1 litre DEKOR-SEAL CLEANER in 1 litre of warm water) with a monobrush equipped with a white disk. Rinse with water (preferably hot water) and allow at least 1 hour drying time, removing any standing water. Apply DEKOR-SEAL WAX pure or diluted 1:1 by volume with water using a wax applicator. Allow 2÷3 hours for the floor to dry before walking on it. The product can be applied in 2 hands spaced apart from each other by at least 1 hour.

 

How to refresh the wax treatment:

the wax layer can be periodically refreshed after ordinary cleaning with DEKOR-SEAL WAX diluted 1:10 with water and applied with wax-spreaders in 1 or 2 coats spaced apart from each other by at least 1 hour. Note: if the existing wax layer is deeply damaged or dirty it is necessary to remove it with STRIPPER PLUS (refer to the Technical Data Sheet) and reapply.

DEKOR-SEAL WAX

Protective wax for
DEKOR SEAL-S500 treated floors

Average Consumption

Applied pure product: 40 - 60 g / m 2

This product was diluted 1:10 with water: 20 - 40 g / m 2

DEKOR-SEAL WAX

Protective wax for
DEKOR SEAL-S500 treated floors

Features

density (at 20 ± 3 ° C), UNI 8310

g/cm³

1.028 ± 0.004

pH, UNI 24003

-

8.80 ± 0.08

Appearance

-

orange-yellow opalescent liquid

Odor/Smell

-

citrus and slightly ammoniacal

dry residue (at 105 ° C, 1 hour)

%

25.2 ± 0.3

Application Temperature

°C

between +5 ° and +35

Note: testing methods are in accordance with the standards referred to in the table.

 

DEKOR-SEAL WAX

Protective wax for
DEKOR SEAL-S500 treated floors

Warning and informations
  • Shake well before use.
  • The product is not suitable for application on antistatic / conductive substrates.
  • Do not apply DEKOR-SEAL WAX over pre-existing damaged or dirty wax layers.
  • The product is not hazardous to health, however, refer to MSDS before use.
  • Keep the product away from heat and direct sunlight, store it in a dry place.
  • The product is frost sensitive and should be stored at temperatures between +5 and +30 ° C.
Preservation

24 months in original packaging, in a covered, dry area at temperatures between +5 ° C and +35 ° C. Frost sensitive.