DEKOR-PLAN

Clear Finish Coat
Ideal for Indoor
Horizontal Surfaces

Description

DEKOR-PLAN is a two-component, solvent-free product specifically developed to protect interior horizontal surfaces that have been previously coated with resin and decorated with specific products such as DEKOR -ART.

 

The product is made up of:

  • Component A: a mixture of liquid epoxy pre-polymers and special fillers;
  • Component B: copolymerization amine.

Once fully cured, the material exhibits a glossy surface and good hardness and scratch resistance properties. The applied film, by its nature, is subject to yellowing, although the thin thickness helps to minimize this effect.

DEKOR-PLAN gives rise to a clear, waterproof, slightly wavy shiny-looking and easy to clean film, especially ideal for use in environments where ease of maintenance and anaesthetics value are required.

Usage field

DEKOR-PLAN is used as a glossy finish on floors or horizontal areas resin's coating, possibly decorated with specific products such as DEKOR -ART.

Packaging

packs of 7.5 kg (A + B)

DEKOR-PLAN

Clear Finish Coat
Ideal for Indoor
Horizontal Surfaces

Application

Product Preparation

  • Pour DEKOR-PLAN component B into component A and mix thoroughly with a low speed professional mixer until the mixture is smooth.
  • allow sufficient time for the induction and de-aeration (2-3 minutes) periods in between the mixing of the two components (A and B) and the laying down of the resin.


Application

Proceed with the application of DEKOR-PLAN with a short haired roller for solvents in one or two coats, 24 hours apart from each other, taking care not to exceed maximum recommended consumption levels.

More over, particular finishes containing FLAKES or glitter can be realized: in this case a final DEKOR-PLAN coat shall be applied to ensure the incorporation of decorative elements.

DEKOR-PLAN

Clear Finish Coat
Ideal for Indoor
Horizontal Surfaces

Average Consumption

150-200 g / m2 per coat.

A product coat gives rise to the formation of a 120-160 mm thick film.

DEKOR-PLAN

Clear Finish Coat
Ideal for Indoor
Horizontal Surfaces

Features

Bulk Density, UNI 8310

g/cm³

1,05 ± 0,05

Pot-Life, UNI EN ISO 9514

 minutes 

30 ± 5

Superficial drying time, UNI 8904

hours

8 ± 1

Curing Minimum Time

days

7

Application Temperature

°C

 from +15 to +35 

UV resistance and condensate, ASTM D 4329 (168 hours exposure)

E

>23

Adhesion to Concrete (pull-off test) ASTM D 4541

MPa

> 3,5

Hardness (Shore D) ASTM D 2240

---

> 70

Abrasion resistance, UNI 8298 / 9

mg

< 120

Superficial brightness determination(gloss 60 °), UNI EN ISO 2813

---

100

Ratio A: B

1.5: 1.0

Note: testing methods are in accordance with the standards referred to in the table.

DEKOR-PLAN

Clear Finish Coat
Ideal for Indoor
Horizontal Surfaces

Warning and informations
  • The addition of solvents to DEKOR-PLAN causes a reduction in chemical resistance, gloss finish and mechanical strength; moreover, this hinders the possibility of applying the product on vertical areas.
  • Apply further layers the following day, after a maximum of 48 hours.
  • In cold weather, product viscosity increases, making it difficult to apply it with a roller, therefore, bring the product to a warm place for a few hours (at 25-30 ° C) before proceeding.
  • The system reaction speed is affected by the temperature: low temperature gradually diminishes speed to zero, while high temperature promotes product's cross-linking, but decreases its pot life.
  • Mix DEKOR-PLAN component A and B according to the precise proportions indicated on the packaging. In case of partial use of the packaging, a scale shall be available to do the weighing.
  • Remove fresh product from all used equipment with ACETONE.
  • Warning: once hardened, the product can only be removed with a flame or hot air above 200 ° C.
  • Please carefully read the Material Safety Data Sheet (MSDS).
Preservation

24 months in original packaging, in a covered, dry area at temperatures between +15 ° C to +30 ° C; cold sensitive.

DEKOR-PLAN

Clear Finish Coat
Ideal for Indoor
Horizontal Surfaces

Solutions number