DEKOR-SEAL S 500

Oil-resistant, decorative and protective coating for floors

Description

DEKOR-SEAL S 500 is an hydrophobicizing, one component product based on non-yellowing thermoplastic acrylic resins dissolved in a solvent.

When applied on concrete or cement mortar surfaces, Dekor-SEAL S 500 has the properties of an impregnation, consolidating and anti-dust agent, giving rise to a transparent glossy film tenaciously bound to the substrate and resistant to exposure to atmospheric agents (light, UV rays, rain, etc. ... ).

This polymeric film protects concrete against various degradation factors, such as:

  • carbonation, preventing carbon dioxide from spreading within the solid matrix;
  • colour fading, preventing the leaching action of rain;
  • corrosion, limiting the penetration of weathering agents (chlorides and sulfates);
  • staining and dirt adhesion, especially fats and oils adhesion;
  • wear and abrasion.

When applied at a thickness of less than 200 microns, DEKOR-SEAL S 500 maintains concrete water vapour permeability and preserves the aesthetic characteristics of the surface. A slight toning (light "wet-effect") is obtained if DEKOR-SEAL S 500 is applied on a blasted or scarified concrete. Due to its high-speed drying, treatment with DEKOR-SEAL S 500 becomes rain resistant in only 2 hours after application.

Usage field

DEKOR-SEAL S 500 is used as a protective treatment both for indoor and outdoor concrete floors. It is ideally suited for:

  • external car parks and large squares;
  • garages and car showrooms;
  • machine shops;
  • warehouses;
  • acid-etched concrete surfaces;
  • concrete surface with aggregates in full view (such as washed gravel, etc. ...).

Due to its chemical properties, DEKOR-SEAL S 500 can be applied after only 8 hours onto moulded concrete manufactured blocks/surfaces, and after just 14 days of curing on concrete floors.

In the civil engineering field, where the aesthetic aspect is of secondary importance, DEKOR-SEAL S 500 can profitably be used as an anti-drying, curing agent for wet concrete.

 

Packaging

1, 5 and 20 litres metal pack.

DEKOR-SEAL S 500

Oil-resistant, decorative and protective coating for floors

Application

A) New concrete flooring

the surface must be dry, cohesive and free of loose or friable areas. Make sure, using a sclerometer, that the concrete compression resistance is at least 25 MPa and check by pull-out test that the cohesion force against tearing is at least 1.2 MPa;

  • compensate the deteriorated areas with GROVE COLABILE or NORDGROUTH TIXO according to need;
  • roughen the surface by high pressure water cleaning: on surfaces that are not quartz hardened, this treatment should be performed giving with particular attention to the areas where bleeding has occurred (which gives rise to a soft, dusty gloss/patina);
  • any possible residue of cured and non permanent products, is to be removed by washing with STRIPPER and / or an high temperature steam treatment;
  • dust and any scales resulting from joints cutting shall be removed by washing thoroughly with water;
  • excess water shall be completely removed by taking care that not standing water is left behind on the area to be treated;
  • Let it dry for 1 or 2 days and then evenly apply DEKOR-SEAL S 500 with a roller, brush or spray (see below spray-output parameters), preventing accumulation that could alter the surface appearance and product curing.

Application Notes-

  • With poorly cohesive substrates, prior to the application of DEKOR-SEAL S 500 the surface shall be treated with CONSOLID PU (follow the instructions given on the technical data sheet).
  • In the case of very compact concrete, a base coat of DEKOR-SEAL S 500 diluted with 10 ÷ 15% of SOLVENTE PER DEKOR-SEAL S is to be applied.
  • On very porous concrete, to prevent the formation of bubbles, the surface must be primed with one coat of DEKOR-SEAL S500 diluted with a 40-50% SOLVENTE PER DEKOR-SEAL S, then DEKOR-SEAL S 500 shall be applied undiluted approximately 2 hours after.
Useful Advices
  • DEKOR-SEAL S 500 can be applied with just one coat;
  • If the absorption by the substrate makes it necessary, more coats must be applied at least 2 hours apart (at +20 ° C) from each other;
  • If room and substrate temperature is lower than +10 ° C or higher than +27 ° C, dilute DEKOR-SEAL S 500 with 5% SOLVENTE PER DEKOR-SEAL S.

 

B) Old concrete flooring

the surface must be dry, cohesive and free of loose or flaky areas. Use a sclerometer to ensure that the compressive strength is at least 25 MPa and perform a pull-out test to check that the tearing strength is at least 1.2 MPa;

  • all degraded areas shall be compensated with GROVE COLABILE or NORDGROUTH TIXO, according to need;
  • surface existing open pores shall be thoroughly cleaned by high pressure water cleaning or acid wash with NORDECAL FORTE detergent, followed by a thorough rinsing and sucking up the resulting liquid;
  • excess water shall be completely removed by taking care that not standing water is left behind on the area to be treated;
  • Let it dry for 1 or 2 days and then evenly apply DEKOR-SEAL S 500 with a roller, brush or spray (see below spray-output parameters, preventing accumulation that could alter the surface appearance and product curing.

Application Notes

  • With poorly cohesive substrates, prior to the application of DEKOR-SEAL S 500, the surface shall be treated with CONSOLID PU (follow the instructions given on the technical data sheet).
  • In the case of very compact concrete, a base coat of DEKOR-SEAL S 500 diluted with 10 ÷ 15% of SOLVENTE PER DEKOR-SEAL S is to be applied.
  • On very porous concrete, to prevent the formation of bubbles, the surface must be primed with one coat of DEKOR-SEAL S 500 diluted with a 40-50% SOLVENTE PER DEKOR-SEAL S, then DEKOR-SEAL S 500 shall be applied undiluted approximately 2 hours after.

 

C) Old,already treated concrete flooring (with intact and resistant treatment):

  • ensure that the adhesion of the existing treatment is higher than 1.0 MPa. If not, see the next section of this technical data sheet;
  • degrease with STRIPPER(insisting on existing wax layers), rinse and suck up the resulting liquid;
  • excess water shall be completely removed, taking care that not standing water is left behind on the area to be treated;
  • identify an area of about 1 m2 to perform a DEKOR-SEAL S 500 application test, allow the product to cure for at least 4 hours, then verify that the DEKOR-SEAL S 500 application did not affect the old treatment;
  • if not, after 1 ÷ 2 days of drying, apply DEKOR-SEAL S 500 as described in Section A;
  • If the coating has been damaged during testing by DEKOR-SEAL S 500 application, follow the instructions given in Section C.

 

D) Old, already treated concrete flooring (with a damaged or not chemically resistant treatment ):

  • whenever the existing treatment has deteriorated (adhesion less than 1.0 MPa) or does not chemically resist to the application of DEKOR-SEAL S 500 it must be completely removed by mechanical methods, such as diamond polishing machine with three heads.

Note: Generally, treatments that do not resist DEKOR-SEAL S 500 are based on water-based, single component acrylic resins;

  • Follow the instructions given in Section A.

 

E) Concrete flooring in Marine Environment or in contact with De-Icing Salts:

  • to impart water repellency to concrete, the surface shall be pre-treated with NORDRY 100 or NORDRY 200 applied in 2 coats wet on wet (max. 1 hour apart from each other);
  • Let it cure for at least 8 hours (at +20 ° C, RH 50%), then proceed with the treatment following the instructions given in Section A.
Product application

Application with roller:

  • short haired roller resistant to organic solvents.

Air Sprayer Application (airbrush):

  • Nozzle diameter: 1.5 ÷2.0 mm
  • Fluid pressure: 1.0 ÷ 2.0 bar
  • Air pressure: 2.0 ÷ 4.0 bar

Airless Sprayer Application :

  • Nozzle diameter: 0.30 ÷ 0.50 mm
  • Output pressure: 80 ÷ 130 bar

When needed dilute with 2 ÷5% SOLVENTE PER DEKOR-SEAL S.

 

Maintenance

Ordinary cleaning of surfaces treated with DEKOR-SEAL S500:

DEKOR-SEAL S 500 -treated surfaces can be washed with DEKOR-SEAL CLEANER, namely an alcohol-based alkaline detergent diluted with water in a ratio of between 1:5 and 1:20 by volume (1 litre of product for 5 or 20 litres of water), depending on the type and amount of dirt. A monobrush equipped with a white disc or an industrial floor cleaning machine (also scrubber dryers machines) can be used. Other types of disc can be used, but their effectiveness should be checked first to avoid damaging the coating. Rinsing is not necessary even if it improves the cleaning treatment performance.

 

To make the DEKOR-SEAL S 500 coating last longer, the surface can be protected with DEKOR-SEAL WAX, a wax in aqueous emulsion with high scratch resistance and gloss effect. A DEKOR-SEAL WAX treatment has the advantage of being easily removable and re-applicable if damaged.

 

How to protect surfaces treated with DEKOR-SEAL S500 using DEKOR-SEAL WAX :

prior to the application of DEKOR-SEAL WAX, the surface must be thoroughly cleaned with DEKOR-SEAL CLEANER diluted 1:1 with hot water (1 DEKOR-SEAL CLEANER litre in 1 litre of warm water) with a monobrush equipped with a white disk. Rinse with water (preferably hot water) and allow at least 1 hour drying time, removing any standing water.

Apply DEKOR-SEAL WAX pure or diluted 1:1 by volume with water using a wax applicator. Allow 2÷3 hours for the floor to dry before walking on it.

 

Ordinary cleaning of the surfaces treated with DEKOR-SEAL WAX:

DEKOR-SEAL WAX treated surfaces can be washed with DEKOR-SEAL CLEANER diluted with water in a ratio of between 1:10 and 1:20 by volume (1 litre of product every 5 or 10 litres of water) depending on the type and the amount of dirt. No need to rinse. Both industrial floor cleaning machines and scrubber dryers machines can be used.

 

How to refresh the wax treatment:

the wax layer can be refreshed after ordinary cleaning by re-treating the floor with DEKOR-SEAL WAX diluted 1:10 with water and applying it with a wax-spreader. If the wax layer is deeply damaged, it is necessary instead to completely remove it and re-apply it.

 

How to remove the wax treatment:

DEKOR-SEAL WAX can be removed from the surface by stripping with STRIPPER PLUS diluted between 1:5 and 1:10 in hot water. Pour the stripper onto the surface and spread it evenly.  Rub the floor with a monobrush equipped with a white disk and allow at least 5 minutes for the product action before removing it. Insist, if necessary, over areas where DEKOR-SEAL WAX treatment has been performed several times. Rinse with clean water.

Once dry, the surface can be re-treated and protected with DEKOR-SEAL WAX, following the previously given instructions. Note: Do not use solvent based strippers because they can damage the underneath DEKOR-SEAL S 500 based treatment. Always test a small floor area first for strippers compatibility before using them.

DEKOR-SEAL S 500

Oil-resistant, decorative and protective coating for floors

Average Consumption

The assessment of coverage should be made by performing a preliminary test. Theoretical concrete coverage: 150 ÷200 g / m 2 each coat.

DEKOR-SEAL S 500

Oil-resistant, decorative and protective coating for floors

Features

Bulk Density (20 ± 3 ° C, 50 ± 10% RH), UNI 8310

g/cm³

0.941 ± 0.005

Kinematic viscosity (ISO cup 4 mm, 20 ± 1 ° C, 50 ± 10% RH), DIN EN ISO 2431

s

69 ± 5

Appearance

-

clear liquid

Odour/Smell

-

aromatic naphtha

Permeability to water vapour - µ (dry cup), DIN 52615

-

12000 ± 1000

Application  temperature

°C

between +5 and +35

Application  maximum humidity

%

85

Dry residual (105 ° C, 1 hour)

%

21 ± 1

Surface drying time (tack free, 23 ± 2 ° C, 50 ± 10% RH), UNI EN ISO 1517

min

30 ± 5

Walkability time (50 ± 10% RH)

h

T = +10 ° C

8

T = +20 ° C

5

T = +30 ° C

4

Operating temperature

°C

between -20 and +70

Note: testing methods are in accordance with the standards referred to in the table.

 

Chemical Resistance

Distilled water

5

Ammonia 15%

5

Bleach (7% active Cl 2)

5

Gas oil

5

Engine oil (SAE 10W-40)

5

Oil gear oil (SAE 85W-140)

5

Caustic Soda 30%

5

Red wine

5

NORDECAL FORTE diluted with water 1:1 by volume

1

STRIPPER diluted 1:5 by volume with water

1

* Compliant with UNI EN ISO 2812-1:1996 - Method 2 (continuous contact with absorbent material).

The effects on the coating are evaluated as shown in Appendix A.

DEKOR-SEAL S 500

Oil-resistant, decorative and protective coating for floors

Warning and informations
  • The product is ready for use, however, shake the container vigorously before use.
  • All equipment used for the application of the product can be washed with SOLVENTE PER DEKOR-SEAL S or alternatively with SOLVENTE PER NORDPUR, SOLVENTE PER NORDCHLOR or nitro diluent.
  • Before application, the product should be kept at room temperature between +15 ° C and + 27 ° C.
  • Do not apply if rain is imminent or expected.
  • Do not apply when relative humidity is above 85%.
  • The application must be carried out at a temperature at least 3°C higher than dew point and never lower than  +5°C.
  • The product is flammable and dangerous to health, refer to the material safety data sheet (MSDS) before use.
  • Keep the product away from heat and direct sunlight, store it in a dry place.
Preservation

24 months in original packaging, in a covered and dry place. At temperatures between +5 ° C to +35 ° C.

DEKOR-SEAL S 500

Oil-resistant, decorative and protective coating for floors

Solutions number