Do you already know what to search?
Clear Filters

Featured products

FLOOR-V

Clear Finish Coat
for Indoor Applications,
for Vertical Surfaces

Description

FLOOR-V is a two-component solvent-free product specifically designed to provide the ultimate protection of internal vertical surfaces, which have been previously treated with resin and decorated with specific products like DEKOR-ART.

 

The product is made up of:

  • Component A: a mixture of liquid epoxy pre-polymers and special fillers;
  • Component B: copolymerization amine.

Once fully cured, the material exhibits a glossy surface and good hardness and scratch resistance properties. The applied film, by its nature, is subject to yellowing, although the thin thickness helps to minimize this effect.

FLOOR-V gives rise to a clear, waterproof, slightly wavy shiny-looking and easy to clean film, especially ideal for use in environments where ease of maintenance and an aesthetics value are required.

 

Usage field

FLOOR-V is used as a glossy finish on epoxy systems applied to walls like W3 COLORATO and appropriately decorated with acrylic systems like DEKOR-ART.

Packaging

Packs of 7.5 kg (A + B)

FLOOR-V

Clear Finish Coat
for Indoor Applications,
for Vertical Surfaces

Product preparation
  • Pour FLOOR-V component B into component A and mix thoroughly with a low speed professional mixer until the mixture is homogeneous.
  • allow sufficient time for the induction and de-aeration (2-3 minutes) periods in between the mixing of the two components (A and B) and the laying down of the resin.
Product application
  • Proceed with the application of FLOOR-V with a short haired roller for solvents in one or two coats, 24 hours apart from each other, taking care not to exceed maximum recommended consumption levels.
  • More over, particular finishes containing FLAKES or glitter can be realized: in this case a final FLOOR - V coat shall be applied to ensure the incorporation of the decorative elements.

FLOOR-V

Clear Finish Coat
for Indoor Applications,
for Vertical Surfaces

Average Consumption

100-120 g / m 2 per coat.

A coat of this product gives rise to a film with a thickness of 80-100 mm

FLOOR-V

Clear Finish Coat
for Indoor Applications,
for Vertical Surfaces

Features

Bulk Density, UNI 8310

g / cm³

1.05 ± 0.05

Pot-Life, UNI EN ISO 9514

min

30 ± 5

Superficial drying time, UNI 8904

Hours

8 ± 1

Curing Minimum Time

days

7

Application Temperature

°C

from +15 to +35

UV resistance and condensate, ASTM D 4329 (168 hours exposure)

∆E

> 23

Adhesion to Concrete (pull-off test) ASTM D 4541

MPa

> 3,5

Hardness (Shore D) ASTM D 2240

---

> 70

Abrasion resistance, UNI 8298 / 9

mg

< 120

Superficial brightness determination(gloss 60 °), UNI EN ISO 2813

---

100

Ratio A: B

1.5: 1.0

Note: testing methods are in accordance with the standards referred to in the table.

FLOOR-V

Clear Finish Coat
for Indoor Applications,
for Vertical Surfaces

Warning and informations
  • The addition of solvents to FLOOR-V causes a reduction in chemical resistances, final gloss and mechanical strength. Moreover, this hinders the possibility of applying the product on vertical areas.
  • Apply further coats the following day, after a maximum of 36 hours.
  • In cold weather, product viscosity increases, making it difficult to apply it with a roller. Therefore, bring the product to a warm place for a few hours (at 25-30 ° C) before proceeding.
  • The system reaction speed is affected by the temperature: low temperature gradually diminishes speed to zero, while high temperature promotes product's cross-linking, but decreases its pot life.
  • Mix FLOOR-V component A and B according to the precise proportions indicated on the packaging. In case of partial use of the packaging, a scale shall be available to do the weighing.
  • Remove fresh product from all used equipment with ACETONE.
  • Warning: once hardened, the product can only be removed with a flame or hot air above 200 ° C.
  • Please carefully read the Material Safety Data Sheet (MSDS)before use.
Preservation

24 months in original packaging, in a covered, dry area at temperatures between +15 ° C to +30 ° C; cold sensitive.

FLOOR-V

Clear Finish Coat
for Indoor Applications,
for Vertical Surfaces

Solutions number