NATURAL COAT LUX

Final protection for polished plaster flooring in the NATURAL range: GLOSS PROTECTIVE FINISH

Description

NATURAL COAT LUX is a water-based bi-component aliphatic finish to be mixed at the time of use. It creates a glossy and transparent final protective layer for polished plaster surfaces in the NATURAL range.

Usage field

NATURAL COAT LUX can be used as finishing and protective coating in the following instances:

  • on finishing layers of cement or epoxy-cement rendering, on floors or on walls;
  • on floors made of concrete or cementitious screed.

The product may also be used on cement and polymer-cement finishing layers of various other natures: nevertheless, as it is designed specifically for use with the NATURAL system, preliminary tests should be carried out first.

Packaging

kit (A+B) - 0,63 kg:

A = 0,49 kg (plastic container); B = 0,14 kg (glass bottle)

kit (A+B) da 1,35 kg:

A = 1,05 kg (plastic container); B = 0,30 kg (glass bottle)

kit (A+B) da 4,5 kg:

A = 3,5 kg (plastic container); B = 1,0 kg (metal can)

NATURAL COAT LUX

Final protection for polished plaster flooring in the NATURAL range: GLOSS PROTECTIVE FINISH

Specific preparation
  • sand the surface with a 180 grade abrasive and completely remove any dust by vacuuming or wiping with a damp cloth;
  • make sure that the laid support has a working level of residual humidity compatible with the product (normally 8±24 hours after laying);
Product preparation

Pour NATURAL COAT LUX comp. B into comp. A and mix thoroughly using a professional mechanical mixer set to a low RPM until a perfect amalgam is achieved.

The resulting mixture should then be diluted with 30-50% water by weight (1 kg of (A+B) and 0.3-0.5 kg of clean water according to ambient temperature: in warm weather use the maximum dilution).

Mix the diluted product and begin application. 

Product application

Apply the product with a short-haired roller in two coats, leaving 5-6 hours between coats. 

NATURAL COAT LUX

Final protection for polished plaster flooring in the NATURAL range: GLOSS PROTECTIVE FINISH

Average Consumption

0,06-0,08 kg/m2 per coat.

NATURAL COAT LUX

Final protection for polished plaster flooring in the NATURAL range: GLOSS PROTECTIVE FINISH

Features

Density at 20°C, UNI 8310

A

g/cm3

1,04 ± 0,03

B

1,02 ± 0,03

A+B

1,02 ± 0,03

Surface drying time, UNI 8904

hours

6 ± 2

Ready for use (dry)

days

3

Ready for use (also for wetting)

days

7

Gloss 60° (on smooth cement rendering), ISO 2813

-

80 ± 5

Minimum temperature for film formation, DIN ISO 2115

°C

10

A:B ratio

3,5 : 1,0

Note: test methods are in accordance with the standard referred to in the table.  

NATURAL COAT LUX

Final protection for polished plaster flooring in the NATURAL range: GLOSS PROTECTIVE FINISH

Warning and informations
  • Once the product has been mixed and is ready for use, it should be used within 30 minutes (at 23°C). After this, the mixture cannot be further diluted to extend its life: take care to observe this timescale because the product does not have a visible pot life (i.e. it does not become thicker or gel-like as with other similar products).Cleaning tools: clean with water if the product is still fresh, or mechanically (or with a naked flame where possible) when the product has hardened.
  • Store in a dry place away from direct sunlight.
  • Carefully read the Safety Sheet. 
Preservation

12 months in original packaging, in a covered, dry area at temperatures between +5°C and +30°C. The product is cold sensitive.